{"id":3493,"date":"2026-10-15T15:39:17","date_gmt":"2026-10-15T07:39:17","guid":{"rendered":"http:\/\/www.testigodecine.com\/blog\/?p=3493"},"modified":"2026-10-15T15:39:17","modified_gmt":"2026-10-15T07:39:17","slug":"what-are-the-factors-affecting-the-soldering-quality-of-pcba-47c8-5f3e40","status":"publish","type":"post","link":"http:\/\/www.testigodecine.com\/blog\/2026\/10\/15\/what-are-the-factors-affecting-the-soldering-quality-of-pcba-47c8-5f3e40\/","title":{"rendered":"What are the factors affecting the soldering quality of PCBA?"},"content":{"rendered":"

If you\u2019re working with PCBA (Printed Circuit Board Assembly), you know how much rides on good soldering. Bad solder joints\u2014cold ones, ones with bridges, or just plain weak ones\u2014can make a whole unit fail, and as someone who\u2019s been in the PCBA supplier game for years, I\u2019ve seen it all. Whether you\u2019re prototyping a new gadget or doing a full production run, soldering quality isn\u2019t just about following steps; it\u2019s a mix of small, interconnected factors that all have to line up right. Let\u2019s break down the big ones that actually matter, no fancy jargon that makes your eyes cross. PCBA<\/a><\/p>\n

<\/p>\n

First up is the solder paste itself. I can\u2019t stress this enough\u2014skimp here and you\u2019re setting yourself up for headaches. Not all solder paste is made the same. There\u2019s leaded and lead-free, but even within those categories, things vary a lot. Solder paste is basically tiny solder balls mixed with flux, right? The flux is the unsung hero here\u2014it cleans the pad and component pin so the solder can actually wet (that\u2019s the term for when solder flows and sticks properly, not just sits there like a drop of water on a waxed car) instead of balling up. If the flux is old, it loses its activity, or if the solder powder is the wrong size\u2014like too big for tiny 0201 resistors or too small that it gets sucked into the stencil holes wrong\u2014you\u2019re going to get bad joints. I\u2019ve had customers come to me saying their last supplier used cheap solder paste that caused 10% of their boards to fail reflow, and that\u2019s just avoidable if you pick the right paste for your specific job.<\/p>\n

Next is stencil design and setup. The stencil is that thin metal sheet you use to print solder paste onto the PCB pads, right? If the stencil is cut wrong\u2014like the holes are too small, too big, or not aligned with the pads\u2014you\u2019re either getting not enough paste (which causes open joints) or too much (which bridges between adjacent pins, super bad for fine-pitch components like microchips). Even the stencil thickness matters: thinner for small, tight pads, thicker for through-hole parts that need more solder. I remember a customer doing a project with a bunch of 0.5mm pitch ICs\u2014their old stencil was 150 microns thick, and they kept getting solder bridges. We switched to a 120-micron stencil with laser-cut square holes instead of round ones, and their failure rate dropped to almost zero overnight. Also, how you clean the stencil between prints? If paste dries in the holes, that\u2019s a blockage, so you gotta do regular cleans with the right solvent, not just a wipe with a paper towel.<\/p>\n

Then there\u2019s the PCB itself\u2014we can call it the board for short, but the surface finish is key here. The pads on the PCB need a surface that the solder can wet to, or again, you get that \u201ccold joint\u201d look where solder just sits on top and doesn\u2019t stick. Common finishes are HASL (hot air solder level), ENIG (electroless nickel immersion gold), OSP (organic solderability preservative), and each has its own pros and cons. OSP is super common for prototyping because it\u2019s cheap, but it doesn\u2019t like being stored for too long\u2014if the board sits in a warehouse for 6 months, the OSP wears off and the solder won\u2019t stick. ENIG is better for long-term reliability, especially for fine-pitch parts, but it\u2019s more expensive. I always tell customers to match the surface finish to their application\u2014if it\u2019s a consumer device that\u2019s going to be made in 10k units, OSP is fine, but if it\u2019s a medical device that\u2019s in a factory, go ENIG. Also, how the pads are designed\u2014too small, or with too much spacing between them, that\u2019s a design flaw that even the best soldering process can\u2019t fix.<\/p>\n

Component preparation is another one that\u2019s easy to overlook. The pins of resistors, capacitors, ICs\u2014they need to be clean and free of oxidation, right? If a component has been sitting in a bag for years, or got exposed to moisture and humidity, the pins can oxidize, so when the solder touches them, it can\u2019t wet properly. For through-hole components, sometimes the leads are tinned (coated with a thin layer of solder) at the factory, but if that tinning is old, it turns into tin whiskers, which are tiny little filaments that can cause short circuits. That\u2019s a big deal for aerospace or automotive parts. We always check components when they come in\u2014if the packaging is damaged, or if the manufacturing date is over 2 years old, we\u2019ll do a test tin to make sure the solder sticks before putting them on a board.<\/p>\n

The soldering process parameters\u2014whether you\u2019re doing reflow soldering (the most common for surface-mount parts) or wave soldering (for through-hole)\u2014are make or break. Let\u2019s talk reflow first, since that\u2019s what most high-mix PCBA uses. Reflow ovens have different zones: preheat, soak, reflow, cool. If the preheat zone is too slow, the solder paste flux doesn\u2019t activate properly, and you get oxidation. If the reflow temperature is too high, you can damage the components\u2014like plastic ICs melting, or resistors changing value. Too low, and the solder never reaches its melting point, so you get cold joints. Even the time at reflow temperature matters\u2014usually 10-30 seconds above the melting point, not longer. For wave soldering, the wave height and conveyor speed are key: if the wave is too low, some pins don\u2019t touch the solder; too high, and you get solder masks on the board getting damaged. I\u2019ve worked with a prototyping customer who kept blowing a few ICs per run because they cranked the reflow temp too high, not realizing that their ICs had a max temp spec of 245C, and the oven was set to 260C. We adjusted the profile, and their component damage went from 8% to less than 1%.<\/p>\n

Environmental conditions during the process\u2014you might not think this matters, but it does. Humidity, temperature, even dust in the air can mess things up. If your assembly area is too humid, moisture can get trapped in the components or the solder paste, which turns into steam during reflow and causes voids in the solder joints. Voids are little air pockets inside the solder; small ones are fine, but big ones can weaken the joint or cause heat buildup. If the area is too cold, especially when printing solder paste, the paste gets too thick and doesn\u2019t spread evenly. We keep our production area at 22C (72F) with 40-50% humidity all year, and we have dehumidifiers in storage areas for boards and components. Last quarter, we had a heatwave where the AC went out for a few hours, and we had a run of 500 boards with a 3% void rate, which is way above our normal 0.5%\u2014so we learned that lesson the hard way.<\/p>\n

Human factor, too\u2014don\u2019t sleep on this, even if most processes are automated. Surface-mount placement machines are super accurate, but if the nozzle is dirty, it might pick up a component at the wrong angle, so it\u2019s sitting crooked on the pad. That leads to bad solder joints, because the pad isn\u2019t fully covered. For hand-soldered prototypes (which a lot of startups do early on), the technician\u2019s skill matters a lot\u2014too much heat and you burn the board or component, too little and the solder doesn\u2019t stick. We have all our techs go through training on soldering processes and quality checks, and we do periodic audits of their joints under a microscope. I\u2019ve seen a tiny mistake\u2014like a tech wiping the soldering iron tip on the wrong cloth\u2014cause a bunch of cold joints, so consistency is key.<\/p>\n

Wait, also post-soldering checks and rework? That\u2019s part of the process too, right? Even if you do everything right, sometimes a joint is bad, so you need to rework it without making it worse. If you use the wrong desoldering tool, or too much heat during rework, you can lift a pad off the PCB, which is a total loss. We have strict rework guidelines\u2014only use a hot air rework station with a temperature controlled tip, and limit the time the heat is on the board. We also do automated optical inspection (AOI) after soldering, which checks for bridges, open joints, wrong components, etc., before the boards go out. AOI isn\u2019t perfect, but it catches a lot of issues before they get to the customer.<\/p>\n

As a PCBA supplier, our whole thing is getting soldering right every single time, no matter if it\u2019s a 10-unit prototype or a 100k unit production run. A bad solder joint doesn\u2019t just mean a failed board\u2014it means the customer has to waste time and money fixing it, and their product might get delayed. That\u2019s why we pay attention to every little factor: not just picking good materials, but calibrating our ovens monthly, checking stencils before every run, training our team, and keeping an eye on even the small stuff like humidity.<\/p>\n

If you\u2019re working on a project that needs PCBA, whether you\u2019re a startup making your first consumer gadget or a established company needing reliable production, getting the soldering right starts with partnering with someone who knows these factors inside and out. We\u2019ve helped tons of customers fix soldering issues they were having with other suppliers\u2014things like persistent solder bridges, high failure rates, or component damage from bad reflow profiles. We take the time to ask about your specific needs: what components you\u2019re using, your board design, production volume, and application, so we can make sure every step of the soldering process is set up for success. No one-size-fits-all here, and we don\u2019t cut corners on solder paste or stencil design just to save a few bucks.<\/p>\n

<\/p>\n

If you\u2019re tired of dealing with bad PCBA soldering that costs you time and money, reach out to us to chat about your project. We\u2019d love to walk through what you need, answer any questions you have, and help you get solid, reliable solder joints that make your product work as intended.<\/p>\n

Massager Gun<\/a> References<\/p>\n

    \n
  1. John H. Lau, "Solder Joint Technology: Materials, Processes, and Reliability," McGraw-Hill, 2005.<\/li>\n
  2. Vikas Gupta, "Printed Circuit Board Assembly and Manufacturing Handbook," McGraw-Hill, 2011.<\/li>\n
  3. IPC-A-610, "Acceptability of Electronic Assemblies," Association Connecting Electronics Industries, 2021.<\/li>\n
  4. K. J. Puttlitz and K. A. Stalter, "Handbook of Lead-Free Soldering Technology," Wiley-IEEE Press, 2004.<\/li>\n<\/ol>\n
    \n

    Jinan Smart New Energy Technology Co., Ltd.<\/a>
    As one of the most professional PCBA manufacturers and suppliers in China, we have world-leading production equipment and strong manufacturing capabilities. Please rest assured to wholesale bulk customized PCBA from our factory. Contact us for quotation and free sample.
    Address: A7 Building, Xingfu Liancheng International Laser Valley, No.688 Chunhui Road, High-Tech Zone, Jinan City
    E-mail: sales@jnsmartenergy.com
    WebSite:     https:\/\/www.junanhealth.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"

    If you\u2019re working with PCBA (Printed Circuit Board Assembly), you know how much rides on good … What are the factors affecting the soldering quality of PCBA?<\/span>Read more<\/a><\/p>\n","protected":false},"author":587,"featured_media":3493,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[3456],"class_list":["post-3493","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-pcba-4687-602c57"],"_links":{"self":[{"href":"http:\/\/www.testigodecine.com\/blog\/wp-json\/wp\/v2\/posts\/3493","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.testigodecine.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.testigodecine.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.testigodecine.com\/blog\/wp-json\/wp\/v2\/users\/587"}],"replies":[{"embeddable":true,"href":"http:\/\/www.testigodecine.com\/blog\/wp-json\/wp\/v2\/comments?post=3493"}],"version-history":[{"count":0,"href":"http:\/\/www.testigodecine.com\/blog\/wp-json\/wp\/v2\/posts\/3493\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.testigodecine.com\/blog\/wp-json\/wp\/v2\/posts\/3493"}],"wp:attachment":[{"href":"http:\/\/www.testigodecine.com\/blog\/wp-json\/wp\/v2\/media?parent=3493"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.testigodecine.com\/blog\/wp-json\/wp\/v2\/categories?post=3493"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.testigodecine.com\/blog\/wp-json\/wp\/v2\/tags?post=3493"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}