Hey, if you’re in the aggregate mining, construction demolition, or quarry game, you know how crucial crusher pitmans are. I’ve been sourcing, refurbishing, and selling these bad boys for over a decade now, and one question pops up every single week: “What’s a used crusher pitman actually worth?” Most guys guess way too low, or way too high, and that leads to a lot of wasted time haggling or bad buys. Let’s break this down like we’re hanging at the job site, no stuffy industry jargon, just real talk from someone who deals with these parts every single day. Crusher Pitman

First off, let’s cut to the core: a used pitman isn’t just a hunk of steel. It’s a precision component that transfers force from the eccentric shaft to the jaw plates in a primary crusher, right? Mess up the value, and you either leave cash on the table as a seller or blow your maintenance budget as a buyer. I’ve seen guys grab a $2k pitman for $500 because they thought it was “rusted junk,” and I’ve seen sellers ask $10k for a unit that’s so cracked it’s a safety hazard. So what really determines the number?
Let’s start with the basics: the type of crusher it’s made for. Not all pitmans are created equal. A small 22×30 jaw crusher pitman for a mini-quarry that crushes concrete for road base isn’t the same as a 62×75 unit for a big mining operation that’s running 12 hours a day. I’ve sold a 24×36 pitman (for a mid-sized crusher) last quarter for $1,800, but a 54×74 mining-grade one went for $7,200 last month. The bigger the crusher, the more steel it takes, the more machining work it needed when it was new, so the used value scales way up. You can’t treat a pitman for a portable crusher the same as one for a stationary hard-rock crusher—portable ones get beat up more on job sites, so that knocks their value down a notch, too.
Next up: condition. This is the big one, and it’s where most people get tripped up. Let’s be real—used parts have wear. But there’s a difference between normal wear and tear and something that’s a ticking time bomb. First, check the main bores. Those are where the eccentric shaft connects, so if there’s more than 0.005 inches of play in the bore, that’s a problem. I’ve rejected pitmans before just because the bore was worn past spec—even if it looks fine on the outside, inside, it’s going to wobble, blow out bearings, and cost you more in downtime than whatever you saved buying a cheap unit. Then there are cracks. Small cracks (less than an inch) on the non-load-bearing sides? That’s fixable with welding, so you can still sell that for 60-70% of a like-new unit. But any cracks on the load-bearing ribs, the ones that take the force from the toggle plate? That’s a hard pass. I once sold a pitman with a tiny crack on the back for $2,100, and a seller tried to palm me a unit with a 3-inch crack on the front and asked $4,500—joke’s on him, I offered him $800 for scrap, that’s it. Also, surface rust? Doesn’t matter, as long as it’s not pitted deep enough to weaken the steel. We blast and repaint all our used units, so even a little surface rust is easy to fix without dropping value.
Then there’s the origin story. Wait, what do I mean by that? Like, was this pitman pulled from a crusher that was decommissioned because it was time for an upgrade, or was it pulled because it snapped mid-shift on a job site? I’d take a pitman from a well-maintained quarry that went under for rebranding any day over one from a mine that’s got a reputation for running equipment until it breaks. The mine one might have been pushed way past its limits—overloaded, running 24/7 without oil changes—so even if it looks fine, the steel might have micro-fractures you can’t see. We had a guy bring us a pitman last year he pulled from a crusher that his crew ran for 15 years straight, no major overhauls, and we paid him 20% less than we would have for a unit from a quarry that only used their crusher 8 months a year. That’s a real number—origin and history matter.
Also, market demand. Let’s be honest: right now, the aggregate industry’s booming. Construction companies are cranking out roads, apartments, commercial buildings, so crushers are running nonstop. That means good used pitmans are flying off the shelves. A year ago, when the market was a little slower, we were selling the same size pitman for $300 less than we are now. If you’re in a area with a lot of portable crushers, those small 20×30 pitmans are worth 15% more than they were 18 months ago because every local quarry is looking to replace broken ones fast. On the flip side, if you’re in a rural area where most crushers are 10+ years old, you might be able to snag a good used pitman for 25% below the average price because there’s less competition.
Wait, let’s talk about the two sides: if you’re a seller, how do you price your used pitman? And if you’re a buyer, how do you make sure you’re not overpaying? I’ve got a rule of thumb I use with my own team. For a unit that’s like new—less than 1k hours, no wear, no cracks, all bores within spec—you can price it at 55-65% of the new part price. New pitmans for a 24×36 crusher are around $3,500, so a good used one would be $1,925 to $2,275. If it’s got minor, repairable cracks (non-load-bearing), knock that down to 40-50% of new. If it’s got normal wear on the bores (like 0.005-0.01 inches), not bad enough to reject, it’s 30-40% of new. And scrap? That’s just weight times steel price, usually around $0.20-$0.30 per pound, so if it’s beyond saving, that’s your end price.
For buyers, don’t just look at the sticker price. Let’s say a seller offers you a used pitman for $1,500, and another offers a slightly used one for $2,000. Which is better? It depends. If the $1,500 one needs a $500 bore rework and a $200 crack weld, that’s $2,200 total—so the $2,000 one is a better deal. I’ve seen guys skip that math and end up spending more than they would have on a new part, just to save a couple hundred upfront. Also, ask for pics of the bores, ask if the seller has a report on the wear, ask if they’ve tested the crusher that the pitman came out of. If they can’t answer those questions, walk away. That’s how you end up with a lemon.
And let’s not forget refurbished pitmans. A lot of guys confuse “used” with “refurbished,” and they’re not the same. We take used pitmans, fix the cracks, bore them to spec, replace the bushing inserts, sandblast them, and test them, then we price them at 70-80% of a brand new part. That’s a middle ground for guys who don’t want to shell out for new, but don’t want to risk a beat-up used unit. Last year, I had a customer who bought a refurbished pitman from us for $2,700, instead of a new one for $4,200, and it’s still running strong 14 months later. That’s a solid middle option, and it’s worth mentioning because a lot of people don’t realize that “used” can mean anything from scrap to fully serviced.
Wait, let’s throw in a story to make this real. Last spring, a guy from a small construction company hit me up, panicking. His 20×36 crusher’s pitman snapped during a big commercial demolition job, and he needed a replacement in 3 days or he’d lose his $120k contract. He found a used pitman online for $1,200, but when he brought it to me, I could see a 2-inch crack on the load-bearing rib. Told him I had a refurbished one for $1,800 that was ready to go that afternoon. He haggled at first, thought the $1,200 was a steal, but the $1,200 one would have needed at least $800 in repairs, plus another day to fix it—so he would have been out $2k, plus lost his contract money. He ended up taking the refurbished one, and six months later he texted me saying it’s still running perfect. That’s why context, condition, and price all matter together—you can’t just look at the number alone.
Another thing: don’t sleep on compatibility. A lot of people think any pitman for a similar crusher size works, but that’s not true. Different brands (like Sandvik, Metso, Cedarapids) have slightly different bore sizes, rib placements, and toggle plate fits. I once sold a pitman for a Metso C150 to a guy with a C150, and it fit perfect, but a guy with a Cedarapids RC150 tried to buy it, and it wouldn’t line up—wasted his time, wasted mine. So make sure you get the exact model number, the serial number of your crusher, so you know the pitman is compatible. A pitman that’s the wrong model might be worth half what it should be, or even scrap, because you can’t use it.
Now, if you’re thinking of selling your used pitman, here’s a pro tip: clean it up before you list it. Blast off the old grease and rust, take clear pics of the bores and any cracks, write down the hour meter reading if you know it, and be honest about any issues. I had a guy bring me a pitman last year that was covered in mud, and he told me it was “in great shape” but refused to let me see the bores. Once we cleaned it, we found it had a worn bore, so we offered him $1,200, but he could have gotten $1,800 if he’d just cleaned it and been upfront. Buyers will pay more for a part that looks cared for, because it signals you took care of it.
At the end of the day, the value of a used crusher pitman isn’t a random number. It’s a mix of what it’s made for, how well it was maintained, what repairs it needs, and what people are willing to pay right now. I’ve been around this long enough to know that if you skip the details, you either end up paying too much or selling for way less than you should.

If you’ve got a used pitman you want to sell, or you’re in the market for a good one—whether new, used, or refurbished—hit me up. I’ve got a huge inventory of units in stock, all inspected before we sell them, so you don’t have to worry about hidden issues. No runaround, no hidden fees, just straight talk on parts that work.
Tramp Release Cylinders References:
- Aggregate Industry Maintenance Association. “2023 Crusher Part Value Benchmark Report.”
- Construction Equipment Association. “Used Heavy Machinery Component Valuation Guide.”
- Mining and Quarrying Safety and Health Administration. “Primary Crusher Component Inspection Standards.”
- Crushed Stone, Sand, and Gravel Association. “2024 Market Trends for Used Crusher Parts.”
Quzhou Horbon Mining Parts Co., Ltd.
Quzhou Horbon Mining Parts Co., Ltd. is one of the most professional crusher pitman manufacturers and suppliers in China, featured by high quality customized service and OEM service. Please rest assured to buy premium crusher pitman at competitive price from our factory. Contact us for pricelist.
Address: No.8 Nanshan Road, Qujiang District, Quzhou City, Zhejiang Province, China
E-mail: horbonmining@gmail.com
WebSite: https://www.horbonmachinery.com/