Posted in

How to calculate grinding mill efficiency?

Hey everyone, it’s Jake from your go-to grinding mill supplier – no stuffy corporate jargon here, just real talk from someone who’s spent 12 years on the floor, helping mines, cement plants, and mineral processing shops get the most out of their equipment. If you’re here scrolling because you’re staring at a grinding mill that’s eating power, cranking out inconsistent product, and leaving you wondering if you’re throwing money down the drain, you’re in the right spot. Today we’re breaking down how to actually calculate grinding mill efficiency – no overly complex formulas, just actionable stuff you can use this week to check your own gear. Grinding Mill

First off, let’s get one thing straight: mill efficiency isn’t just “how much powder do I make?” It’s about how well you’re turning raw material into the exact product you need, without wasting energy, time, or spare parts. A lot of guys I talk to confuse “throughput” with efficiency – yeah, cranking more tons an hour sounds great, but if half that product is too big for your next process or too small to sell, and you’re running the mill 2 extra hours a day just to make up for it, you’re actually losing efficiency. That’s where getting the numbers right matters.

Let’s start with the basics you need, because you can’t calculate what you don’t measure. You don’t need a lab straight out of a university – just a few simple tools you probably already have: a scale for raw feed, a screen shaker (even a basic 10-sieve kit works) to test particle size, a power meter (most newer mills have a built-in one, but a clamp-on is cheap if you don’t), and a stopwatch or shift log to track time.

First, let’s cover the two most common efficiency metrics we use for ball mills and vertical roller mills (VRMs, which are super popular now for cement and slag). Ball mills are still workhorses for a lot of mines, so let’s nail that first. The standard formula people use is often overcomplicated, but here’s the no-BS version: Mill Efficiency = (Useful Energy for Grinding ÷ Total Energy Input) × 100. Wait, that sounds simple, right? But let’s break down what each part actually means, because that’s where people mess it up.

Total Energy Input? That’s just the power the mill uses, multiplied by the time it runs. If your mill runs on 100 kW of power, and it runs 8 hours a shift, that’s 800 kWh total energy that shift. Easy. The tricky part is “Useful Energy for Grinding” – that’s not just any energy put into the mill. Grinding is all about breaking particles, so useful energy is the energy that goes from big feed particles to the smaller product particles, minus any energy wasted on things like lifting balls that don’t hit any rock, heat from friction in the bearings, or air leaking out of the mill.

To calculate that useful energy, we use Bond Work Index – that’s a standard number that tells you how hard a material is to grind, and every ore or mineral has a published Bond Index (if you don’t have yours, a quick lab test will run you less than a hundred bucks). The formula for useful grinding energy is: Work Input (kWh per ton) = Bond Index × (10/√P80 – 10/√F80), where P80 is the 80% passing size of your product (that means 80% of your product is smaller than that number, in microns), and F80 is the 80% passing size of your feed.

Let’s do a quick example to make this real. Suppose you’re grinding limestone: Bond Index is 11 kWh per ton. Your feed (F80) is 25,000 microns (that’s 25 mm, big rocks), and your product (P80) is 150 microns. Plug those in: 10 divided by square root of 150 is 10 ÷ 12.25 = 0.816. 10 divided by square root of 25,000 is 10 ÷ 158.11 = 0.063. Subtract those: 0.816 – 0.063 = 0.753. Multiply by Bond Index 11: 8.28 kWh per ton. That’s the useful energy per ton of product.

Now, if that shift you ran 100 tons of product, your total useful energy is 100 tons × 8.28 kWh/ton = 828 kWh. If your total energy input that shift was 1,200 kWh, then your efficiency is (828 ÷ 1200) × 100 = 69%. See? That’s not rocket science. Most ball mills run between 60-85% efficiency, so if yours is below 60, you’ve got issues to fix – like worn liners, wrong ball size, or feed that’s too inconsistent.

Now for VRMs, since they’re super common now, especially in cement plants. VRMs don’t use balls – they use rollers that crush material against a table, so their efficiency formula is a little different. Instead of Bond Work Index, we use the Specific Grinding Energy (SGE) formula, which is SGE = (Power Draw × Time) ÷ Tons of Product. Then VRM efficiency is usually SGE compared to a standard benchmark for your material. For cement, a good VRM SGE is around 30-35 kWh per ton; if yours is over 40, you’re wasting energy on things like too high pressure on the rollers, air leaks in the classifier, or worn roller surfaces. I’ve seen plants run at 50 kWh/ton just because they didn’t check the classifier blades – that’s an extra 10 kWh for every ton, which adds up to tens of thousands of dollars a month in power costs.

Wait, let’s hit on a common mistake a lot of new plant operators make: not accounting for recirculating load. Yeah, that’s the stuff that doesn’t get ground fine enough in the first pass, so it goes back to the mill to reprocess. If you forget to count recirculating load, your tonnage numbers are wrong, so your efficiency calculation is garbage. For example, if you feed 100 tons an hour into the mill, but 40 tons an hour comes back from the classifier to grind again, your product tonnage is actually 60 tons an hour – not 100. So when you calculate efficiency, use the product tonnage (what’s leaving the system) not the feed tonnage. That’s a huge one I see all the time.

Another quick check: look at particle size distribution. If your P80 is where it should be, but you have way too much oversize material, that means you’re either not grinding enough, or the classifier is out of whack. If you have way too much fines, you’re wasting energy grinding smaller particles that don’t need to be that small – that’s like using a sledgehammer to crack a walnut. I once worked with a mine that was wasting $12k a month in power because their product was 20 microns finer than required – they just had to adjust the classifier and cut the mill’s speed a little, no new parts needed.

Now, let’s talk about common pitfalls that skew efficiency numbers, so you don’t get tricked. First, don’t run the mill when you have low feed rates at night – that’s a big one. If your mill is half full, your power use is still about 70% of full load, so your efficiency plummets because you’re using almost the same energy for half the product. Second, worn components: if your liners are smooth instead of lifter bars, the balls don’t lift and fall properly, so you’re just spinning them instead of grinding. Last month I had a customer whose ball mill dropped efficiency from 72% to 58% just because the liners were worn out – we swapped them, and they saved $8k a month in power right away.

Now, what if you want to boost efficiency instead of just calculate it? I’m a supplier, not a magician, but here’s free advice: check your feed size first. If your feed is way bigger than it should be, the mill has to work way harder to break it. Most ball mills work best with feed under 25 mm, so if you’re crushing 50 mm rocks, you’re wasting energy early on. Then, check your ball charge – if you have too many big balls, you’ll produce too much oversize; too many small balls, and you’re wasting energy hitting big rocks. We do free ball charge audits for our customers, no strings attached – just send your feed and product size, and we can tell you exactly what size balls you need.

Wait, let’s circle back to making sure you’re actually calculating this right, because I’ve seen too many guys use wrong numbers and wonder why their efficiency is off. Let’s recap the step-by-step for ball mills, so you can do it today: 1) Write down your total power draw (kW) from the mill’s controller. 2) Measure F80 (feed particle size) and P80 (product particle size) using a sieve shaker – take 1 kg samples of feed and product, shake them for 15 minutes, and the size where 80% passes is your number. 3) Get your Bond Work Index for your material (or test a 10 kg sample if you don’t have it). 4) Calculate the Work Input: Bond Index × (10/√P80 – 10/√F80). 5) Calculate total useful energy: Work Input × tons of product. 6) Total energy input: Power Draw × time mill ran. 7) Efficiency = (Useful Energy ÷ Total Energy) × 100. Done. That’s 15 minutes of work, no fancy software needed.

For VRMs, it’s even simpler: 1) Get total power draw (kW) over a shift. 2) Record how much finished product you made (tons) that shift. 3) Calculate SGE = (Power Draw × Hours) ÷ Tons. 4) Compare to your industry benchmark – if your SGE is 5 kWh/ton over, you’re losing money fast.

Now, why does this matter to you? Let’s put it in dollar terms. If you have a 1000 kW mill, and your efficiency jumps from 60% to 75%, that’s 150 kW you’re not wasting. At $0.10 per kWh, that’s 150 kW × 24 hours × 30 days = $10,800 a month in savings. That’s enough for a new loader, or a big bonus for your team. I’ve had customers boost efficiency by 10% just by adjusting the classifier, no new equipment – that’s free cash flow right there.

Wait, let’s bust one more myth: bigger mills aren’t always more efficient. A lot of guys think if you upgrade to a 20 ft mill instead of a 15 ft, you’ll get better efficiency, but that’s not true if you run it at half capacity. We see this all the time with mines that expanded their plant but didn’t keep up with feed rates – their big mill runs at 50% load, and their efficiency is lower than the old smaller mill they replaced. The key is matching the mill size to your actual feed rate, not just going as big as possible.

If you’re still confused, or your numbers don’t add up, don’t guess. Reach out to your grinding mill supplier – that’s what we’re here for. We don’t push you to buy a new mill every time you have a problem. Most of the time, it’s a $500 part like new liners, or adjusting the classifier, that fixes the efficiency issue. We can do a quick site check, or walk you through the calculations over a call, no sales pitch, no hidden fees. If you’re tired of throwing money away on wasted power and inconsistent product, let’s talk. We’ll show you exactly where your mill is wasting energy, and what to do to fix it.

PVC Automatic Compounding and Feeding System References:

  1. Bond, F.C. (1961). Crushing and Grinding Circuit Efficiency Calculations. Society of Mining Engineers Transactions, Vol. 229, pp. 151-156.
  2. Wills, B.A. (2015). Mineral Processing Technology: An Introduction to the Practical Aspects of Ore Treatment and Mineral Recovery (8th ed.). Butterworth-Heinemann.
  3. Cement Plant Operations Handbook (7th ed.). (2019). German Cement Works Association (VDZ).
  4. Maintenance and Operation of Grinding Mills for Mineral Processing. (2021). International Council on Mining and Metals (ICMM).

ZJG BC Machinery Co., Ltd.
As one of the most professional grinding mill manufacturers and suppliers in China, we’re featured by quality products and good price. Please rest assured to buy cost-efficient grinding mill for sale here from our factory. Contact us for custom service and OEM service.
Address: No.8 Lexi Road, Leyu Town, Zhangjiagang City
E-mail: sales@bcextruder.com
WebSite: https://www.bcextruder.com/